If it guesses wrong, the CREATE_CHILD_SA exchange fails, and it will have to retry with a different KEi. If the SA offers include different DH groups, KEi must be an element of the group the initiator expects the responder to accept. A Notify Payload might appear in a response message (usually specifying why a request was rejected), in an informational exchange (to report an error not in an IKE request), or in any other message to indicate sender capabilities or to modify the meaning of the request. Help would really be appreciated. New here? Accepted Solutions. Zscaler support IP-SLA HTTP probes to check the cloud proxy health, on traditional routers you are able to use 'track' features to, for example, change the admin distance of a static route based on the results of the IP-SLA test. Initiator receives response from Responder. Responder sends the response for IKE_AUTH. cEdge supports standard IKE tunnels in 19.x. Router 1 receives the IKE_SA_INIT response packet from Router 2. Which Interface did you use? I notice the guide was written for the vEdge. 4 Sep 18 2018 17:40:58 750003 Local:80.x.y.z:500 Remote:51.a.b.c:500 Username:51.a.b.c IKEv2 Negotiation aborted due to ERROR: Detected unsupported . Source Interface in my setup is the WAN Interface connected to the Internet. IKEv2 Packet Exchange and Protocol Level Debugging, Technical Support & Documentation - Cisco Systems, Router 1 receives a packet that matches the crypto acl for peer ASA 10.0.0.2. Relevant Configuration:crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5, *Nov 11 19:30:34.832: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_WAIT_AUTH Event: EV_RECV_AUTH *Nov 11 19:30:34.832: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_WAIT_AUTH Event: EV_CHK_NAT_T *Nov 11 19:30:34.832: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_WAIT_AUTH Event: EV_PROC_ID *Nov 11 19:30:34.832: IKEv2:(SA ID = 1):Received valid parameteres in process id *Nov 11 19:30:34.832: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_WAIT_AUTH Event: EV_CHK_IF_PEER_CERT_NEEDS_TO_BE_FETCHED_FOR_PROF_SEL *Nov 11 19:30:34.832: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_WAIT_AUTH Event: EV_GET_POLICY_BY_PEERID *Nov 11 19:30:34.833: IKEv2:(1): Choosing IKE profile IKEV2-SETUP *Nov 11 19:30:34.833: IKEv2:% Getting preshared key by address 10.0.0.1 *Nov 11 19:30:34.833: IKEv2:% Getting preshared key by address 10.0.0.1 *Nov 11 19:30:34.833: IKEv2:Adding Proposal default to toolkit policy *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):Using IKEv2 profile 'IKEV2-SETUP' *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_WAIT_AUTH Event: EV_SET_POLICY *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):Setting configured policies *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_WAIT_AUTH Event: EV_VERIFY_POLICY_BY_PEERID *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_WAIT_AUTH Event: EV_CHK_AUTH4EAP *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_WAIT_AUTH Event: EV_CHK_POLREQEAP *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_VERIFY_AUTH Event: EV_CHK_AUTH_TYPE *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_VERIFY_AUTH Event: EV_GET_PRESHR_KEY *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_VERIFY_AUTH Event: EV_VERIFY_AUTH *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_VERIFY_AUTH Event: EV_CHK4_IC *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_VERIFY_AUTH Event: EV_CHK_REDIRECT *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):Redirect check is not needed, skipping it *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_VERIFY_AUTH Event: EV_NOTIFY_AUTH_DONE *Nov 11 19:30:34.833: IKEv2:AAA group authorization is not configured *Nov 11 19:30:34.833: IKEv2:AAA user authorization is not configured *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_VERIFY_AUTH Event: EV_CHK_CONFIG_MODE *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_VERIFY_AUTH Event: EV_SET_RECD_CONFIG_MODE *Nov 11 19:30:34.833: IKEv2:Received config data from toolkit: *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_VERIFY_AUTH Event: EV_PROC_SA_TS *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_VERIFY_AUTH Event: EV_GET_CONFIG_MODE *Nov 11 19:30:34.833: IKEv2:Error constructing config reply *Nov 11 19:30:34.833: IKEv2:No config data to send to toolkit: *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_BLD_AUTH Event: EV_MY_AUTH_METHOD *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_BLD_AUTH Event: EV_GET_PRESHR_KEY *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_BLD_AUTH Event: EV_GEN_AUTH *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_BLD_AUTH Event: EV_CHK4_SIGN *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_BLD_AUTH Event: EV_OK_AUTH_GEN *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: R_BLD_AUTH Event: EV_SEND_AUTH *Nov 11 19:30:34.833: IKEv2:Construct Vendor Specific Payload: CISCO-GRANITE *Nov 11 19:30:34.833: IKEv2:Construct Notify Payload: SET_WINDOW_SIZE *Nov 11 19:30:34.833: IKEv2:Construct Notify Payload: ESP_TFC_NO_SUPPORT *Nov 11 19:30:34.833: IKEv2:Construct Notify Payload: NON_FIRST_FRAGS, *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):Next payload: ENCR, version: 2.0 Exchange type:IKE_AUTH, flags:RESPONDER MSG-RESPONSEMessage id: 1, length: 252 Payload contents: ENCR Next payload: VID, reserved: 0x0, length: 224 *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: AUTH_DONE Event: EV_OK *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):Action: Action_Null *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: AUTH_DONE Event: EV_PKI_SESH_CLOSE *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):Closing the PKI session *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: AUTH_DONE Event: EV_UPDATE_CAC_STATS *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: AUTH_DONE Event:EV_INSERT_IKE *Nov 11 19:30:34.834: IKEv2:Store mib index ikev2 1, platform 60 *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: AUTH_DONE Event: EV_GEN_LOAD_IPSEC *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):Asynchronous request queued *Nov 11 19:30:34.834: IKEv2:(SA ID = 1): *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState:AUTH_DONEEvent: EV_NO_EVENT, *Nov 11 19:30:34.834: IKEv2:Got a packet from dispatcher *Nov 11 19:30:34.834: IKEv2:Processing an item off the pak queue, *Nov 11 19:30:34.840: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: AUTH_DONE Event: EV_OK_RECD_LOAD_IPSEC *Nov 11 19:30:34.840: IKEv2:(SA ID = 1):Action: Action_Null *Nov 11 19:30:34.840: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: AUTH_DONE Event: EV_START_ACCT *Nov 11 19:30:34.840: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: AUTH_DONE Event: EV_CHECK_DUPE *Nov 11 19:30:34.840: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000001 CurState: AUTH_DONE Event: EV_CHK4_ROLE, *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):Next payload: ENCR, version: 2.0 Exchange type:IKE_AUTH, flags:RESPONDER MSG-RESPONSEMessage id: 1, length: 252 Payload contents: *Nov 11 19:30:34.834: IKEv2:Parse Vendor Specific Payload: (CUSTOM) VID Next payload: IDr, reserved: 0x0, length: 20 IDrNext payload: AUTH, reserved: 0x0, length: 12 Id type: IPv4 address, Reserved: 0x0 0x0 AUTHNext payload: SA, reserved: 0x0, length: 28 Auth method PSK, reserved: 0x0, reserved 0x0 SANext payload: TSi, reserved: 0x0, length: 40 last proposal: 0x0, reserved: 0x0, length: 36 Proposal: 1, Protocol id: ESP, SPI size: 4, #trans: 3 last transform: 0x3, reserved: 0x0: length: 8 type: 1, reserved: 0x0, id: 3DES last transform: 0x3, reserved: 0x0: length: 8 type: 3, reserved: 0x0, id: SHA96 last transform: 0x0, reserved: 0x0: length: 8 type: 5, reserved: 0x0, id: Don't use ESN TSiNext payload: TSr, reserved: 0x0, length: 24 Num of TSs: 1, reserved 0x0, reserved 0x0 TS type: TS_IPV4_ADDR_RANGE, proto id: 0, length: 16 start port: 0, end port: 65535 start addr: 0.0.0.0, end addr: 255.255.255.255 TSr Next payload: NOTIFY, reserved: 0x0, length: 24 Num of TSs: 1, reserved 0x0, reserved 0x0 TS type: TS_IPV4_ADDR_RANGE, proto id: 0, length: 16 start port: 0, end port: 65535 start addr: 0.0.0.0, end addr: 255.255.255.255 *Nov 11 19:30:34.834: IKEv2:Parse Notify Payload: SET_WINDOW_SIZE NOTIFY(SET_WINDOW_SIZE) Next payload: NOTIFY, reserved: 0x0, length: 12 Security protocol id: IKE, spi size: 0, type: SET_WINDOW_SIZE *Nov 11 19:30:34.834: IKEv2:Parse Notify Payload: ESP_TFC_NO_SUPPORT NOTIFY(ESP_TFC_NO_SUPPORT) Next payload: NOTIFY, reserved: 0x0, length: 8 Security protocol id: IKE, spi size: 0, type: ESP_TFC_NO_SUPPORT *Nov 11 19:30:34.834: IKEv2:Parse Notify Payload: NON_FIRST_FRAGS NOTIFY(NON_FIRST_FRAGS) Next payload: NONE, reserved: 0x0, length: 8 Security protocol id: IKE, spi size: 0, type: NON_FIRST_FRAGS *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_WAIT_AUTH Event:EV_RECV_AUTH *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):Action: Action_Null *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_CHK4_NOTIFY *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event:EV_PROC_MSG *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_CHK_IF_PEER_CERT_NEEDS_TO_BE_FETCHED_FOR_PROF_SEL *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_GET_POLICY_BY_PEERID *Nov 11 19:30:34.834: IKEv2:Adding Proposal PHASE1-prop to toolkit policy *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):Using IKEv2 profile 'IKEV2-SETUP' *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_VERIFY_POLICY_BY_PEERID *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_CHK_AUTH_TYPE *Nov 11 19:30:34.834: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_GET_PRESHR_KEY *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event:EV_VERIFY_AUTH *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_CHK_EAP *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event:EV_NOTIFY_AUTH_DONE *Nov 11 19:30:34.835: IKEv2:AAA group authorization is not configured *Nov 11 19:30:34.835: IKEv2:AAA user authorization is not configured *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_CHK_CONFIG_MODE *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_CHK4_IC *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_CHK_IKE_ONLY *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: I_PROC_AUTH Event: EV_PROC_SA_TS *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: AUTH_DONE Event: EV_OK *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):Action: Action_Null *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: AUTH_DONE Event: EV_PKI_SESH_CLOSE *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):Closing the PKI session *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: AUTH_DONE Event: EV_UPDATE_CAC_STATS *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: AUTH_DONE Event: EV_INSERT_IKE *Nov 11 19:30:34.835: IKEv2:Store mib index ikev2 1, platform 60 *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: AUTH_DONE Event: EV_GEN_LOAD_IPSEC *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):Asynchronous request queued *Nov 11 19:30:34.835: IKEv2:(SA ID = 1): *Nov 11 19:30:34.835: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001 CurState: AUTH_DONE Event: EV_NO_EVENT *Nov 11 19:30:34.835: IKEv2:KMI message 8 consumed. E.g. Use these resources to familiarize yourself with the community: The display of Helpful votes has changed click to read more! *Nov 11 19:30:34.835: IKEv2:KMI message 12 consumed. The connection uses a custom IPsec/IKE policy with the UsePolicyBasedTrafficSelectors option, as described in this article.. At the moment,you can use service side ipsec in cedge. In this document . what i am missing here. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. #address 10.0.0.2. This does present a bit of a problem for inteligent traffic steering. IPSEC profile: this is phase2, we will create the transform set in here. This is the CREATE_CHILD_SA request. Be aware the static route will only be withdrawn from the routing table if the Tunnel goes down. Customers Also Viewed These Support Documents, https://www.cisco.com/c/en/us/support/docs/security/flexvpn/115907-config-flexvpn-wcca-00.html. I also had to mention the same ACL in the local policy for this to work. Local Type = 0. description Cisco AnyConnect IKEv2 ip unnumbered GigabitEthernet0/0 tunnel mode ipsec ipv4 tunnel protection ipsec profile staff Take a break, you have now completed the main config on the router, and its time to move onto configuration relating to the client. The packet exchange in IKEv2 is radically different from packet exchange in IKEv1. It seems like it's not passing domain information. Find answers to your questions by entering keywords or phrases in the Search bar above. Could you please clarify, as I'm waiting for this feature being available for some months now. Cisco recommends that you have knowledge of the packet exchange for IKEv2. The vulnerability is due to incorrect handling of crafted IKEv2 SA-Init packets. Hi, can you please post the config that solved your problem. For a branch office VPN that uses IKEv1, the Phase 1 exchange can use Main Mode or Aggressive Mode. You can also check the output of theshow crypto sessioncommand on both routers; this output shows the tunnel session status as UP-ACTIVE. Relevant Configuration:crypto ipsec transform-set TS esp-3des esp-sha-hmac crypto ipsec profile phse2-prof set transform-set TS set ikev2-profile IKEV2-SETUP, *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_BLD_AUTH Event:EV_GEN_AUTH *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_BLD_AUTH Event: EV_CHK_AUTH_TYPE *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_BLD_AUTH Event: EV_OK_AUTH_GEN *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_BLD_AUTH Event: EV_SEND_AUTH *Nov 11 19:30:34.831: IKEv2:Construct Vendor Specific Payload: CISCO-GRANITE *Nov 11 19:30:34.831: IKEv2:Construct Notify Payload: INITIAL_CONTACT *Nov 11 19:30:34.831: IKEv2:Construct Notify Payload: SET_WINDOW_SIZE *Nov 11 19:30:34.831: IKEv2:Construct Notify Payload: ESP_TFC_NO_SUPPORT *Nov 11 19:30:34.831: IKEv2:Construct Notify Payload: NON_FIRST_FRAGS Payload contents: VID Next payload: IDi, reserved: 0x0, length: 20 IDiNext payload: AUTH, reserved: 0x0, length: 12 Id type: IPv4 address, Reserved: 0x0 0x0 AUTHNext payload: CFG, reserved: 0x0, length: 28 Auth method PSK, reserved: 0x0, reserved 0x0 CFGNext payload: SA, reserved: 0x0, length: 309 cfg type: CFG_REQUEST, reserved: 0x0, reserved: 0x0, *Nov 11 19:30:34.831: SA Next payload:TSi, reserved: 0x0, length: 40 last proposal: 0x0, reserved: 0x0, length: 36 Proposal: 1, Protocol id: ESP, SPI size: 4, #trans: 3 last transform: 0x3, reserved: 0x0: length: 8 type: 1, reserved: 0x0, id: 3DES last transform: 0x3, reserved: 0x0: length: 8 type: 3, reserved: 0x0, id: SHA96 last transform: 0x0, reserved: 0x0: length: 8 type: 5, reserved: 0x0, id: Don't use ESN TSiNext payload: TSr, reserved: 0x0, length: 24 Num of TSs: 1, reserved 0x0, reserved 0x0 TS type: TS_IPV4_ADDR_RANGE, proto id: 0, length: 16 start port: 0, end port: 65535 start addr: 0.0.0.0, end addr: 255.255.255.255 TSrNext payload: NOTIFY, reserved: 0x0, length: 24 Num of TSs: 1, reserved 0x0, reserved 0x0 TS type: TS_IPV4_ADDR_RANGE, proto id: 0, length: 16 start port: 0, end port: 65535 start addr: 0.0.0.0, end addr: 255.255.255.255, NOTIFY(INITIAL_CONTACT) Next payload: NOTIFY, reserved: 0x0, length: 8 Security protocol id: IKE, spi size: 0, type: INITIAL_CONTACT NOTIFY(SET_WINDOW_SIZE) Next payload: NOTIFY, reserved: 0x0, length: 12 Security protocol id: IKE, spi size: 0, type: SET_WINDOW_SIZE NOTIFY(ESP_TFC_NO_SUPPORT) Next payload: NOTIFY, reserved: 0x0, length: 8 Security protocol id: IKE, spi size: 0, type: ESP_TFC_NO_SUPPORT NOTIFY(NON_FIRST_FRAGS) Next payload: NONE, reserved: 0x0, length: 8 Security protocol id: IKE, spi size: 0, type: NON_FIRST_FRAGS *Nov 11 19:30:34.832: IKEv2:(SA ID = 1):Next payload: ENCR, version: 2.0 Exchange type:IKE_AUTH, flags:INITIATORMessage id: 1, length: 556 Payload contents: ENCR Next payload: VID, reserved: 0x0, length: 528 *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001CurState: I_WAIT_AUTHEvent: EV_NO_EVENT, *Nov 11 19:30:34.832: IKEv2:Got a packet from dispatcher *Nov 11 19:30:34.832: IKEv2:Processing an item off the pak queue *Nov 11 19:30:34.832: IKEv2:(SA ID = 1):Request has mess_id 1; expected 1 through 1 *Nov 11 19:30:34.832:IKEv2:(SA ID = 1):Next payload: ENCR, version: 2.0 Exchange type:IKE_AUTH, flags:INITIATORMessage id: 1, length: 556 Payload contents: *Nov 11 19:30:34.832: IKEv2:Parse Vendor Specific Payload: (CUSTOM) VID Next payload: IDi, reserved: 0x0, length: 20 IDiNext payload: AUTH, reserved: 0x0, length: 12 Id type: IPv4 address, Reserved: 0x0 0x0 AUTH Next payload: CFG, reserved: 0x0, length: 28 Auth method PSK, reserved: 0x0, reserved 0x0 CFG Next payload: SA, reserved: 0x0, length: 309 cfg type: CFG_REQUEST, reserved: 0x0, reserved: 0x0 *Nov 11 19:30:34.832: attrib type: internal IP4 DNS, length: 0 *Nov 11 19:30:34.832: attrib type: internal IP4 DNS, length: 0 *Nov 11 19:30:34.832: attrib type: internal IP4 NBNS, length: 0 *Nov 11 19:30:34.832: attrib type: internal IP4 NBNS, length: 0 *Nov 11 19:30:34.832: attrib type: internal IP4 subnet, length: 0 *Nov 11 19:30:34.832: attrib type: application version, length: 257 attrib type: Unknown - 28675, length: 0 *Nov 11 19:30:34.832: attrib type: Unknown - 28672, length: 0 *Nov 11 19:30:34.832: attrib type: Unknown - 28692, length: 0 *Nov 11 19:30:34.832: attrib type: Unknown - 28681, length: 0 *Nov 11 19:30:34.832: attrib type: Unknown - 28674, length: 0 *Nov 11 19:30:34.832:SANext payload: TSi, reserved: 0x0, length: 40 last proposal: 0x0, reserved: 0x0, length: 36 Proposal: 1, Protocol id: ESP, SPI size: 4, #trans: 3 last transform: 0x3, reserved: 0x0: length: 8 type: 1, reserved: 0x0, id: 3DES last transform: 0x3, reserved: 0x0: length: 8 type: 3, reserved: 0x0, id: SHA96 last transform: 0x0, reserved: 0x0: length: 8 type: 5, reserved: 0x0, id: Don't use ESN TSiNext payload: TSr, reserved: 0x0, length: 24 Num of TSs: 1, reserved 0x0, reserved 0x0 TS type: TS_IPV4_ADDR_RANGE, proto id: 0, length: 16 start port: 0, end port: 65535 start addr: 0.0.0.0, end addr: 255.255.255.255 TSr Next payload: NOTIFY, reserved: 0x0, length: 24 Num of TSs: 1, reserved 0x0, reserved 0x0 TS type: TS_IPV4_ADDR_RANGE, proto id: 0, length: 16 start port: 0, end port: 65535 start addr: 0.0.0.0, end addr: 255.255.255.255. I think i have the problem with the Source Interface (i receive"IKEv2-ERROR:Address type not supported" in log). This is the CREATE_CHILD_SA response. IOS XE routers must source IPSEC interfaces from the Service side VPN (not VPN0), but also, it is necessary to add a inbound IPv4 ACL to the Interface in VPN0 to permit UDP 500 (IPSEC) and if using NAT UDP 4500 as well.After the tunnel is established you can add a IPv4 static route on the Service side with a next hop of the Tunnel interface to route traffic via the tunnel. This section lists the configurations used in this document. #proposal cisco. This document describes Internet Key Exchange version 2 (IKEv2) debugs on Cisco IOS when a pre-shared key (PSK) is used. If this CREATE_CHILD_SA exchange is not rekeying an existing SA, the N payload must be omitted. Initiates SA creation, *Nov 11 19:30:34.811: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=0000000000000000 (I) MsgID = 00000000 CurState: IDLE Event: EV_INIT_SA. Click the Add button to insert a new VPN rule. The CHILD_SA packet typically contains: Router 1 receives the response packet from Router 2 and completes activating the CHILD_SA. Find answers to your questions by entering keywords or phrases in the Search bar above.
Kington Recycling Centre Booking,
Yakuza 7 Gold Egg,
Maneskin Members Gender,
Articles C